BIG BLOCK FORD
Would you like to react to this message? Create an account in a few clicks or log in to continue.
BIG BLOCK FORD

BIG BLOCK FORD TECHNICAL AND PARTS SITE

OAKLEY MOTORSPORTS ENGINES, CUSTOM CARBS, COMPLETE ENGINE MACHINING, PORTING SERVICE AND DYNO SERVICE. CALL 270-344-0912, 270-929-5185


Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

5 posters

BIG BLOCK FORD :: GENERAL TECH :: ENGINE TECH

Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  ED468 January 31st 2019, 3:18 pm

Used to see Speeedpro around in 4.39 sizes left over. With all the changes Clevite/Mahle and such thought there bee a small chance someone making a performance ring for the 5/64 and .030 overbore. Just got some new OLD stock 429 forgings , with 11 to one would like a good ring.

ED468

Posts : 199
Join date : 2013-03-27
Location : Maunie il.

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Re: Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  pmrphil February 1st 2019, 9:46 am

You can always try Total Seal - if they don't have it, they can probably make it.

pmrphil

Posts : 170
Join date : 2016-10-29

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Re: Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  fordguy69 February 1st 2019, 6:30 pm

Sealed Power and Total Seal both have them. Ordered a set of both in the last couple months through Summit.


fordguy69

Posts : 98
Join date : 2011-08-02

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty I've seen them in the past on summit, tried looking them up and figured they sold outnew old stock..,Thanks I call.

Post  ED468 February 3rd 2019, 3:03 am

Plasma moly rings What i'm looking for with ductile top ring thanks again.

ED468

Posts : 199
Join date : 2013-03-27
Location : Maunie il.

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Re: Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  rmcomprandy February 3rd 2019, 12:57 pm

ED468 wrote:Plasma moly rings What i'm looking for with ductile top ring thanks again.

Personally, I would use a Total Seal "Ring spacer" with a 1/16" or .043" ring

rmcomprandy

Posts : 6108
Join date : 2008-12-02
Location : Roseville, Michigan

http://www.rmcompetition.com

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Re: Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  gt350hr February 5th 2019, 8:11 pm

Speed Pro "E296K +.030" cheap from Summit.

gt350hr

Posts : 662
Join date : 2014-08-20
Location : Anaheim , CA

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Re: Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  rmcomprandy February 5th 2019, 8:23 pm

gt350hr wrote:Speed Pro "E296K +.030" cheap from Summit.

That ring set has a moly top ring but, it is not "Ductile Iron". Merely a cast iron, moly ring.

rmcomprandy

Posts : 6108
Join date : 2008-12-02
Location : Roseville, Michigan

http://www.rmcompetition.com

Back to top Go down

Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring? Empty Re: Do they make a ductile Iron ring 5/64 X 4.39 bore or whats a good ring?

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

BIG BLOCK FORD :: GENERAL TECH :: ENGINE TECH

 
Permissions in this forum:
You cannot reply to topics in this forum