BIG BLOCK FORD
Would you like to react to this message? Create an account in a few clicks or log in to continue.

557" Iron CJ Build

+16
Moodyblues
torinocobra429scj
bbf-falcon
IDT-572
BRONCOBILLY7.5
jm
bruno
The Mad Porter
Curt
ToddB
TorinoGT
Lem Evans
schmitty
bigblockfox468
ThndrChkn
Mark Laczo
20 posters

Go down

557" Iron CJ Build Empty 557" Iron CJ Build

Post  Mark Laczo August 19th 2010, 10:19 am

Engine specs

DOVE block, cemented to wp holes, 4-bolt Milodon Caps, torque plate honed
4.44" JE flat top gas ported, low tension rings setup for Nitrous gap for later
4.5" Scat forged crank
6.8" GRP Aluminum rods
Kasse Oil pump
Moroso rear sump eliminator pan

Heads

Iron CJ's Fully Ported by Scott Johnson Intakes just reaching 390 @.800"
Comp 947's, Ti retainers, Kasse +.100 valves, Comp girdle

Delta Cam Scotty J spec'd 276/286 @ .050 .752"/.771" on a 113 Lb sep

New TFS Intake 4500
1250 Qfuel carb

On the third pull we hit my goal for above 800 horsepower !
Ran 11 more pulls to fine tune jets, carb spacers, timing, headers, and fuels.

Ended making 845hp & 712tq

Dyno sheets attached.

All runs were with Hedman Hustlers fenderwell exit truck headers with 2" x 3.5"(EGT Bungs) On the 836hp pull the oil temp got high at the end and engine was shut down and recorded the low oil psi on the graph, Next pull it was right back.

On the 845hp run there no EGTs as those were my 2 1/4" x 4" Uprights ceramic coated.

I am very pleased with the results to say the least. All info and parts from members and venders on this site. Dyno sheets below.

Thanks, not in any particular order for either parts or advice from a-z

Scott Johnson
Lem Evans
Randy Malik
Frank Merkle

557" Iron CJ Build 557Dyno

557" Iron CJ Build 557Dynouprights




Mark Laczo
Mark Laczo

Posts : 274
Join date : 2009-08-06
Age : 56
Location : Rimbey, Alberta

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  ThndrChkn August 19th 2010, 11:16 am

Dandy numbers Mark. Very impressive with iron heads. Heck, that's impressive with aluminum heads. Very Happy







Doug... Cool
ThndrChkn
ThndrChkn

Posts : 2216
Join date : 2008-12-04
Age : 57
Location : Helena, Montana

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  bigblockfox468 August 19th 2010, 1:32 pm

ThndrChkn wrote: Very impressive with iron heads........Heck, that's impressive with aluminum heads.

X2 cheers
bigblockfox468
bigblockfox468
BBF CONTRIBUTOR
BBF CONTRIBUTOR

Posts : 1432
Join date : 2009-02-09
Age : 101
Location : Dryden, MI

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  schmitty August 19th 2010, 1:53 pm

Nice numbers there Mark. Too bad you couldn't have had a comparison between the TFS and the Victor intakes. That thing is going to boogie in the mud pits. Twisted Evil
schmitty
schmitty

Posts : 4538
Join date : 2008-12-02
Age : 53
Location : Holdrege, NE

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  Lem Evans August 19th 2010, 1:54 pm

cheers

Lem Evans

Posts : 7445
Join date : 2008-12-03
Location : Livermore , Ky

http://bfevansraceparts.com

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  TorinoGT August 19th 2010, 4:53 pm

Wow... with iron heads!? awesome!
TorinoGT
TorinoGT

Posts : 174
Join date : 2009-08-13
Location : Metro Detroit

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  ToddB August 19th 2010, 8:32 pm

Nice build for a sweet truck.

ToddB

Posts : 35
Join date : 2009-09-10
Location : Morriston,Fl

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  Curt August 19th 2010, 9:04 pm

557" Iron CJ Build Sweet-1
Curt
Curt

Posts : 2787
Join date : 2009-02-08
Age : 61
Location : Henrietta, Texas but mostly on the road

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  The Mad Porter August 21st 2010, 7:33 pm


Nicely done Mark.

Just shows that it takes a village to raise a hell raising stroker...


Very Happy



The Mad Porter
The Mad Porter

Posts : 230
Join date : 2009-08-07
Age : 60
Location : Tacoma, Washington

http://www.reincarnation-automotive.com

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  bruno August 21st 2010, 7:57 pm

very nice numbers ...props to all involved !!!! .....

_________________
coming soon x275 build .........
thanks to all my sponsors :

www.OakleyMotorsports.com
www.Induction-Solutions.com
www.bfevansraceparts.com
www.ultimateconverter.com
www.keithfulpmotorsports.com
bruno
bruno
Moderator
Moderator

Posts : 10873
Join date : 2008-12-02
Age : 51
Location : MILLBROOK , AL.

http://WWW.CKRME.COM

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  jm August 24th 2010, 1:46 pm

TorinoGT wrote:Wow... with iron heads!? awesome!
yep!! them old dooe-r's can rock the chevy world Wink i personally know my self Smile

jm

Posts : 65
Join date : 2009-08-06

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  BRONCOBILLY7.5 August 24th 2010, 5:36 pm

Very impressive numbers for some ole FOMOCO iron. Congrats. Billy
BRONCOBILLY7.5
BRONCOBILLY7.5

Posts : 44
Join date : 2009-08-12
Age : 58
Location : OK

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  IDT-572 August 24th 2010, 7:38 pm

When I swapped my TFS Street's off and put my ported Cast SCJ's on nothing changed on the combo no tuning or anything , it ran with in a tenth of the aluminum ported heads. That was with one point less compression and 100 more pounds.

Another point to make here is the exhaust only flowed 50% of the intake and still made power. I guess that kind of blows the Chevy guys therory of you cant make power unless your exhaust flows atleast 70 % of your intake. Twisted Evil Rolling Eyes Laughing

The old Ford iron are bad mamajamma's. I always wanted to put the right cam in mine and tune it on the dyno to see what it would make. The TFS's made 860 hp.

You have a nice power plant............... Cool Congrats to you. Wink
IDT-572
IDT-572
BBF CONTRIBUTOR
BBF CONTRIBUTOR

Posts : 4628
Join date : 2008-12-02
Age : 63
Location : Shelbyville Tn.

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  bbf-falcon August 24th 2010, 10:14 pm

Very nice build. Very Happy

bbf-falcon

Posts : 8995
Join date : 2008-12-03
Location : Jackson, Ohio

Back to top Go down

557" Iron CJ Build Empty Wow! Great numbers...

Post  torinocobra429scj November 30th 2010, 10:38 pm

What an awesome powerplant you have!!! Great job guys
torinocobra429scj
torinocobra429scj

Posts : 30
Join date : 2010-11-11
Age : 53
Location : Flemingsburg, KY

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  Moodyblues December 3rd 2010, 3:14 pm

Dang I need that in my tube chassis mustang to see what it would run! I have ported D0Ve's on my 514 and the must not be flowing enough, lol
Moodyblues
Moodyblues

Posts : 1168
Join date : 2009-08-19
Age : 64
Location : Jasper, TN

http://www.russhoodinsurance.com

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  maxxoffroad December 6th 2010, 1:25 am

That is sweet. I have a set of the DO0E heads and a set of pi's. I have been considering selling the pi's jut to get alum for weight. I might just hang on to them.
maxxoffroad
maxxoffroad

Posts : 45
Join date : 2010-02-15
Age : 52
Location : Katy Tx

http://www.lonestaraxle.com

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  Tony M December 6th 2010, 11:20 pm

Holy Shit Exclamation Exclamation Exclamation I Just saw this thread. Awsome piece. Try that with a IRON PRODUCTION head BBC. You will need a big blower or large shot of juice to even come CLOSE.
Tony M
Tony M

Posts : 479
Join date : 2010-01-17
Age : 54
Location : North Jersey

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  bb429power December 6th 2010, 11:38 pm

Thunderstruck wrote:Holy Shit Exclamation Exclamation Exclamation I Just saw this thread. Awsome piece. Try that with a IRON PRODUCTION head BBC. You will need a big blower or large shot of juice to even come CLOSE.
Yeah, most definantly. And yet they are worshipped??? Way to go man, impressive Smile
bb429power
bb429power

Posts : 3129
Join date : 2010-02-13
Age : 29
Location : Michigan

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  72mav December 7th 2010, 10:48 am

Nice build!! Congrats! Hard to beat factory iron.
BTW, your membership to the "Poor-boys iron motor cub" is pre-approved Laughing Wink
Check out my signature.
Regards.
Al
72mav
72mav

Posts : 1081
Join date : 2008-12-03
Age : 60
Location : central Michigan

Back to top Go down

557" Iron CJ Build Empty Re: 557" Iron CJ Build

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum